Corrected 21 November 2026. An earlier version of this page said two of the five utes in our dual cab comparison could never tow the 3,500kg they advertise. Both can. That claim took the tow ball off the combined figure, which the section on GCM below explains is wrong, and What a dual cab can actually tow withdrew it on 16 November.
Check your own combination
Off the compliance plate
Loaded for the trip
| Limit | The sum | Against | Verdict |
|---|---|---|---|
| GVM | 2,350 + 300 + 350 = 3,000 | 3,280 | 280kg spare |
| Braked tow rating | 3,500 | 3,500 | exactly at it |
| Tow ball download | 350 | 350 | exactly at it |
| GCM | 2,350 + 300 + 3,500 = 6,150 | 6,000 | over by 150kg |
The most this loaded car may tow is 3,350kg. Loaded to its own GVM it is 2,720kg.
These are the worked example's figures.
The four numbers
Three of them are stamped on the compliance plate or the tyre placard, under the bonnet or inside the driver's door opening. The fourth is on the tow bar.
| Number | What it limits | Where to read it |
|---|---|---|
| GVM | The car's own laden mass | Compliance plate |
| GCM | The car and the trailer together | Compliance plate |
| Braked towing capacity | The whole trailer | Owner's handbook or the maker's specification |
| Tow ball download | What the trailer presses down with | Tow bar label, and the handbook |
Gross Vehicle Mass is the maximum laden mass of the car. Gross Combination Mass is the maximum of the car's laden mass plus the axle loads of whatever it is towing. Both are the manufacturer's figures under the Australian Design Rules.
Braked towing capacity is an Aggregate Trailer Mass figure, so it is the whole trailer including what the tow ball is carrying. It is not the mass on the trailer's own wheels.
Two different kerb figures circulate and they are not the same number. Kerb mass is the car in running order with every fluid reservoir full, fuel included. Tare mass is the same car with ten litres in the tank. Western Australia publishes both definitions side by side. Use the heavier one. Being conservative is the right direction.
Tow ball download
This is the one that catches people. The mass pressing down on the tow ball has to go somewhere, and it goes onto the car's rear axle. So it counts against GVM, alongside the passengers, the fuel, the canopy and the gear.
Tow ball download should sit at roughly 8 to 10 per cent of the loaded trailer. On a 3,500kg trailer that is 280kg to 350kg, and it comes straight out of what the car was going to carry.
What a dual cab can actually tow measures that on five utes. All five can tow the 3,500kg they advertise, and doing it costs them 320kg to 600kg of the payload printed beside it.
GCM and the tow ball
Work the combination out the long way and the ball download appears twice. It adds to the car's laden mass and it comes off the trailer's axles, so the two cancel.
Which means the GCM sum is simpler than it looks. It is the car, plus everything in and on the car, plus the whole trailer. The ball figure never enters it.
That matters because the ball download is the one figure people try to solve the problem with. Shifting load forward onto the ball does not buy a single kilogram against GCM. It only moves mass from the trailer's axles onto the car's.
A worked example
Here is the shape, on round figures rather than a named car. Read your own four off the plate.
| The car's ratings | kg |
|---|---|
| GVM | 3,280 |
| GCM | 6,000 |
| Braked towing capacity | 3,500 |
| Maximum tow ball download | 350 |
| Loaded for the trip | kg |
|---|---|
| Kerb mass | 2,350 |
| People, fuel, canopy and gear | 300 |
| Trailer, loaded | 3,500 |
| Tow ball download | 350 |
Now the four checks.
| Limit | The sum | Against | Verdict |
|---|---|---|---|
| GVM | 2,350 + 300 + 350 = 3,000 | 3,280 | 280kg spare |
| Braked towing capacity | 3,500 | 3,500 | exactly at it |
| Tow ball download | 350 | 350 | exactly at it |
| GCM | 2,350 + 300 + 3,500 = 6,150 | 6,000 | over by 150kg |
Every individual rating is respected. The trailer is at its braked tow rating and not a kilogram over. The ball is at its limit and not over. The car has 280kg of its own capacity unused. And the combination is 150kg illegal.
Western Australia's own towing guide says the same thing in a sentence. It may not be possible to tow a trailer at its braked capacity if the car is at its maximum weight without exceeding the GCM.
The fix is 150kg out of the trailer or 150kg out of the car. Taking it off the trailer and putting it in the car does nothing at all, because GCM counts both.
Three towing answers for one car
All three come out of those four plate figures, and only the first one gets advertised.
| Question | Answer | Why |
|---|---|---|
| What does the brochure say | 3,500kg | Braked towing capacity |
| What can this loaded car tow | 3,350kg | 6,000 less the 2,650 the car weighs loaded |
| What if the car is at full GVM | 2,720kg | 6,000 less 3,280 |
That last row is Rated Towing Capacity, and the Australian Design Rules define it as the lesser of the tow bar's own rating and GCM minus GVM. On this example it is 2,720kg. That is 780kg under the advertised figure.
So a car loaded to its own limit tows less than the same car carrying nothing, and the brochure figure describes neither.
GVM upgrades
Upgrading GVM lets the car carry more. It does not raise GCM, it does not raise braked towing capacity, and on its own it makes the towing position worse rather than better.
Western Australia puts the consequence plainly. Upgrading the GVM without upgrading the GCM reduces the weight of trailer that can be towed when the vehicle is loaded to its new maximum mass.
Read that against the arithmetic above and it follows. GCM is fixed, the car is now allowed to be heavier, and the combination limit has not moved, so every extra kilogram of permitted payload is a kilogram the trailer can no longer have.
The Commonwealth settled the GVM and GCM question separately in October 2019. A federal second stage manufacturer approval for a GVM upgrade has never covered the GCM.
Fitting softer springs afterwards voids it. Both Western Australia and the Northern Territory make the point as a condition. A type approval holds only while the approved components, or equivalent rated ones, are the components on the car. Swap in a softer spring because the ride is harsh and the original manufacturer's ratings apply again.
GCM upgrades
GCM carries forces a GVM upgrade never considers. Western Australia lists what has to be assessed, and it runs to the chassis, the engine, the driveline, the braking system, the differential, the cooling system, the tow bar and the stability of the whole combination.
Queensland has a code for it and so does Western Australia, both of them requiring component testing, performance testing and SAE J2807 testing. Western Australia's bulletins were built on the Queensland code, with the Australian Automotive Aftermarket Association.
Braked towing capacity is where the states split hardest. Queensland allows it to be re-rated. Western Australia, the Northern Territory and Tasmania forbid it outright.
| Jurisdiction | Can braked towing capacity be re-rated |
|---|---|
| Queensland | Yes, under code LS16, with GCM |
| Western Australia | No, only the manufacturer may set it |
| Northern Territory | No, only the manufacturer may set it |
| Tasmania | No, the manufacturer's figure stands |
Tasmania's manual puts the two halves in one sentence. There are no provisions in Tasmanian law to allow the towing capacity to be changed for an in service vehicle, and there are provisions for the manufacturer's GVM and GCM to be changed if the vehicle is modified.
So the same work on the same car is available in one state and unavailable in three. That is not a drafting accident. Western Australia's towing capacity rule sits in the Road Traffic (Vehicles) Act 2012 and Tasmania's in the Vehicle and Traffic (Vehicle Operations) Regulations 2014.
Suspension
A heavier spring does not raise a rating. The rating is a number on a plate and only a certifier or the manufacturer can move it. South Australia describes the components a GVM increase may require, and the list runs to springs, dampers, tyres and cooling changes.
What suspension work does trigger is certification in its own right, and the threshold is where the states stop agreeing.
| Jurisdiction | When a lift needs certifying |
|---|---|
| NSW | The lesser of 50mm or a third of the suspension's working travel |
| Victoria | Over 75mm of total lift, counting tyres, for an off road 4WD |
| Queensland | Codes cover a high lift up to 150mm |
| Northern Territory | Over 50mm of lift, or 100mm of overall height, leaves the streamlined path |
New South Wales is the tightest and the reason is the second half of its test. Its own worked example on a 2022 Subaru BRZ computes a third of working travel as 26.6mm at the front and 31.6mm at the rear, so on that car a 30mm lift needs a certificate. A reader who remembers only the 50mm has the rule backwards.
The Northern Territory measures lift as the vertical distance from the centre of the axle to the lowest edge of the body or wheel guard, and its 100mm overall height test counts suspension lift, body lift and larger tyres together.
Before and after first registration
The two paths are genuinely different, and which one a car took follows it for the rest of its life.
Before. A brand new car modified before it is first registered goes through the Commonwealth. Only a federally approved second stage manufacturer, or one of their approved contractors, may fit the kit, and the kit itself needs federal approval. South Australia records that such a car may be registered without requiring the state's own approval and without a roadworthiness inspection.
After. A car already on the road is the state's business, and every jurisdiction has its own scheme, its own certifier and its own paperwork.
The gap between them produces an outcome that reads as unfair and is simply two systems meeting. Western Australia answers the question directly. Two identical cars with identical GVM upgrades, one done before registration and one after, do not get the same GCM, because an unapproved GCM re-rating is not applicable in Western Australia whichever path the car took.
Who signs it off, state by state
Eight jurisdictions, eight schemes, and the sequencing is the part that costs money when it is wrong.
| Jurisdiction | Certifier | Asked before the work |
|---|---|---|
| NSW | VSCCS licensed certifier | No |
| Victoria | VASS signatory | No, recommended |
| Queensland | Approved Person | No for a coded job, yes for an uncoded one |
| WA | Automotive consultant | Yes, approval in principle first |
| SA | Licensed Vehicle Engineering Signatory | Yes, before the work starts |
| Tasmania | Approved Vehicle Certifier | No |
| NT | Recognised engineering signatory | Committee, unless a precedent exists |
| ACT | Recognised engineering signatory | No, certify then inspect |
Western Australia and South Australia both want the application first. Western Australia runs six stages, and the work cannot start until Vehicle Safety and Standards has granted approval in principle and issued a letter with a reference number. South Australia asks the owner to apply prior to the modification being undertaken, then issues a Statement of Requirements for the signatory to work to.
The Northern Territory has a committee. Significant and extensive modifications go to a Technical Advisory Committee, an industry based body that assists the department. A GVM upgrade can skip it, but only through a streamlined path that exists where precedence has been established, and only two ways in. Replicate a second stage manufacturer vehicle using the exact components, or combine the axle ratings the original manufacturer specified.
Everywhere else you build first and certify after. Victoria recommends talking to a signatory before starting and does not require it. New South Wales recommends seeking advice and requires only that the certificate exists before the car is used on a road.
Victoria's certificate expires. A VASS approval certificate issued to a light vehicle is valid for 30 days from the date of issue, where the heavy vehicle equivalent never expires. Miss the month and the inspection is done again.
Crossing a border
This is the question nobody asks before the work and everybody asks after, and the eight answers do not agree.
| Jurisdiction | Another state's certificate |
|---|---|
| NSW | Not recognised |
| WA | Not recognised for a WA registered car |
| Tasmania | Recognised |
| ACT | Accepted, case by case |
| NT | Interstate signatories may be used |
| Queensland | Warns its own may not travel |
New South Wales is the blunt one. Compliance certificates for light vehicles issued under a scheme other than the VSCCS are not recognised in New South Wales.
Tasmania is the opposite. Modification plates legitimately certifying work performed in other states and territories are recognised by its Registrar of Motor Vehicles, and a car modified interstate with no plate at all may still be certified on the documents, at the discretion of Vehicle Registration and Standards.
Western Australia separates two cases that sound like one.
- Touring through. A re-rating certified in the state the car is registered in is recognised everywhere else while travelling. Western Australia's own example is a Queensland certified Patrol on a lap of the country.
- Moving there. A GCM re-rating applies to a Western Australian registered car only where Western Australia approved it, and Western Australian law requires a car garaged in the state to be registered in the state. Its own example is a Perth buyer of a Melbourne re-rated LandCruiser, and the answer is that the original manufacturer's specifications apply.
Western Australia gives its reason, and it is the honest one. There is currently no harmonised GCM upgrade process.
Queensland and the Northern Territory both warn about the same thing from the other side. Queensland tells owners that approvals issued by a Queensland Approved Person may not be recognised in another state. The Northern Territory tells them a vehicle acceptable on Northern Territory registration may not be accepted for registration by another jurisdiction.
So the question to ask is not where the car is now. It is where it will be registered in three years.
Plate figures and road rules
Nothing above changes the four numbers. GVM, GCM, braked towing capacity and tow ball download are the manufacturer's figures under national rules, and they read the same in every state. A car that is 150kg over GCM is 150kg over in all eight.
What does change by state is who approves a change to them, what has to be told to the registry, and some of the rules about towing itself.
An unbraked trailer stops at 750kg. South Australia states it and it is the national figure. Above that the trailer needs its own brakes, and the braked rating is the one on the car's specification sheet.
A light vehicle stops at 4,500kg GVM. Every jurisdiction read for this page uses the same line. Past it the car is a heavy vehicle, and South Australia notes the licence classes that follow.
Watch for an ADR category change. A GVM increase can push a car from one ADR category to the next, and the Northern Territory requires the certification to address compliance with the rules for the new category.
What to do about it
Read your own four numbers off your own plate before you buy either the car or the trailer. Then do the GCM sum first, because it is the one that fails while everything else passes.
If an upgrade is on the table, settle three things in this order. Which jurisdiction will register the car, whether that jurisdiction wants the application before the work, and whether GCM moves with GVM or stays where it is. Getting the third one wrong is how a car ends up legally heavier and able to tow less.
Where this applies
- What a dual cab can actually tow, where the tow ball download on two of five utes is more than the car has left to give.
Sources
- Gross Vehicle Mass, Gross Combination Mass, Aggregate Trailer Mass, Gross Trailer Mass and Rated Towing Capacity as the lesser of the tow bar rating and GCM minus GVM, that braked towing capacity is based on Aggregate Trailer Mass, that it may not be possible to tow at braked capacity with the car at GVM, the 8 to 10 per cent tow ball figure, the kerb and tare definitions, the six stage approval process, that only the manufacturer may re-rate towing capacity under the Road Traffic (Vehicles) Act 2012, that a GVM upgrade without a GCM upgrade reduces what can be towed, that softer springs invalidate the approval, the components a GCM re-rating must address, the touring and the moving cases, and that there is no harmonised GCM upgrade process: transport.wa.gov.au, GVM and GCM FAQs, page updated 3 December 2025, and Modify a light vehicle, Complex, both read 13 November 2026.
- That the Commonwealth separated GVM and GCM approval in October 2019: Administrator's Circular 0-4-6, cited by transport.wa.gov.au as above.
- That a GVM change needs a VASS approval certificate, that the certificate is valid for 30 days from issue for a light vehicle and does not expire for a heavy one, the modify then certify sequence, the blue modification plate, and the 75mm total lift allowance for an off road 4WD: transport.vic.gov.au, Vehicle Assessment Signatory Scheme approval certificate, and VSI 8 Guide to modification for motor vehicles, published October 2021, both read 13 November 2026.
- That re-rating GVM or GCM is item 51, that an interstate certificate is not recognised, and that the suspension threshold is the lesser of 50mm or a third of working travel with the Subaru BRZ worked example: Transport for NSW, Vehicle Standards Information VSI.06 Light vehicle modifications, revision 4, issued 1 July 2026, read 13 November 2026.
- The four Queensland modification tiers, that a specific modification needs the Vehicle Standards Unit's written approval first, that a Queensland approval may not be recognised interstate, and the Section LS codes LS9, LS10, LS11, LS15 and LS16: Department of Transport and Main Roads, Queensland Road Vehicle Modification Handbook, September 2024, read 13 November 2026.
- That LS16 covers Gross Combination Mass and Braked Towing Capacity for a light vehicle: Queensland Code of Practice Vehicle Modifications, code LS16, publications.qld.gov.au, read 13 November 2026.
- That towing capacity cannot be modified on a light vehicle, that GVM and GCM can, that an interstate modification plate is recognised, and the Section S rating codes: Department of State Growth, Vehicle Modification Certification Manual version 4, June 2024, read 13 November 2026.
- The streamlined GVM pathway and its two options, the 50mm and 100mm thresholds and how lift is measured, that GCM does not increase from a GVM upgrade, that the trailer's laden mass may need reducing to stay within GCM, that only the manufacturer may set towing capacity, that type approvals hold only with the approved components, the ADR category change requirement, and that an NT modified vehicle may not be accepted elsewhere: Northern Territory Department of Infrastructure, Planning and Logistics, Information Bulletin V32(lv)(a), 24 June 2023, and nt.gov.au approval processes for modifications, both read 13 November 2026.
- That certification happens before inspection, that interstate reports are accepted case by case and may need recertifying, and the owner certified against significant or extensive split: Access Canberra, Modified light vehicles, read 13 November 2026.
- The 4,500kg light vehicle line, the 750kg unbraked trailer limit, the components a GVM increase may require, that a pre registration re-rating may be registered without the state's approval or a roadworthiness inspection, and that the owner must apply prior to the modification being undertaken with a Statement of Requirements issued to a Licensed Vehicle Engineering Signatory: sa.gov.au, light vehicle mass re-rating, page last updated 2 November 2026.
Citations without a date of their own were read on 13 November 2026.
We do not publish a discount figure. We will when we can measure one honestly, and not before.